point-to-point control

Compared with conventional point-to-point control systems , the advantages of NCS are less wiring , lower install cost as well as greater agility in diagnosis and maintenance .

与传统的点对点控制系统相比，网络控制系统具有布线少、低成本及诊断维护方便等特点。

Based on automotive LAN CAN-bus ' the traditional point-to-point control circuit for AUDI headlamp is transformed to two signal wires according to the singlechip principle .

以汽车控制局域网CAN总线为基础，结合单片机原理，对奥迪汽车前照灯传统的点对点控制电路进行改造，实现了只用2根信号线就可以对奥迪汽车前照灯进行控制；

Iterative Learning Control Based on T-S Model and Its Simulation Study on Point-to-Point Control of Robots

基于T-S模型的迭代学习控制算法及其在机器人点位控制中的仿真研究

Compared to traditional point-to-point control system , network controlsystem is full distributed and more advanced .

网络化控制系统具有完全的分布化、开放性等特点，比传统的点对点控制拥有更大的优势。

In this dissertation , a general framework of the integrated design method for a point-to-point control is presented .

在本文中，提出了针对点位控制的一体化设计方法的大体框架。

The NCSs are replacing the traditional point-to-point control systems that have not satisfied with new requirements .

传统控制的点对点通讯方式已经不能适应某些新的要求，基于网络控制系统正在取代这种方式的控制系统。

Which has developed the pneumatic system from traditional point-to-point control way to servo control way , greatly widen the application area of pneumatic system .

电-气比例／伺服控制技术的出现，使气动系统从传统的点位控制向伺服控制过渡，大大拓展了气动技术的应用领域。

Compared to traditional point-to-point control system , the network control system has fewer connections , low-cost , shared resources , as well as ease of installation and maintenance advantages .

相对于传统的点对点式的控制系统，网络控制系统具有较少的连线，低成本，可以共享资源，以及易于安装和维护等优点。

Compared to traditionally point-to-point control systems , the primary advantages of an NCS are reducing system wiring , easiness of system diagnosis and maintenance , and increasing system agility .

与传统的点对点式的控制系统相比，NCS可以大大减小系统的布线数，并且易于扩展和维护。

Compared with traditional point-to-point control systems , networked control systems have many advantages , such as low installation cost , ease of diagnosis and maintenance , and flexibility of operation and so on .

相对于传统的点对点直接连接的控制系统而言，网络化控制系统有许多优点。例如，系统的安装费用低廉，系统的维护比较容易以及系统的操作也相对简单等。

However , with the complexity of control tasks and diversification of control devices , the traditional point-to-point control mode cannot cope with a large , distributed , and more collaborative axis control requirements .

随着控制任务复杂化、控制设备多样化，传统的点对点的控制方式已不能满足其大规模、分布式、多轴协同的控制要求。

Comparing with the conventional point-to-point control systems , NCSs present a number of advantages , such as low cost , reduced system wiring , ease of system diagnosis and maintenance , and increased system agility .

与传统的点对点的控制系统相比，这种网络化的控制模式避免了控制节点间专线的敷设，减少布线，易于系统的诊断和维护，增加系统结构的灵活性，有效的降低了系统成本。

A special type of iterative learning control ( ILC ) problem is considered , which deals with the point-to-point control of robots . Fuzzy control design method is introduced to solving the special iterative learning control problem .

考虑了一类特殊的迭代学习控制问题，即用迭代学习方法解决机器人的点位控制问题。

In the last few decades , with the rapid developments of communication , computer and control technology , the traditional point-to-point control architecture cannot meet the required performance of control systems and changes to the networked control counterpart .

近几十年来，随着通信、计算机和控制技术的飞速发展，传统的点对点控制模式已经不能满足不断提高的控制系统性能要求，并使得控制模式向网络化控制模式的转变。

Results show that the control accuracy of the point-to-point control of a pneumatic system with single action cylinder is satisfactory to the accuracy requirements of the general purpose reciprocating mechanism . Accordingly , it is of great significance to the extension of the application of pneumatic control systems .

研究结果表明，单作用气缸点位控制系统，其控制精度能满足常用往复机构的要求，因此对扩大气动控制系统的应用是很有意义的。

The problem of optimal parameter design in Point-to-Point motion control was analyzed .

对单纯点到点控制方式下的最优参数设计问题进行了设计与分析。

A Fluidic Point-to-point Positioning Control System

射流点位控制系统

To improve the reliability of communication , the rule of point-to-point error control and the addition of a byte of check sum are introduced into the system .

在通信中，提出了增加一个字节校验和以及端端差错控制的通讯机制，提高了系统通信的可靠性；

Due to the defects of the IP protocol itself , it cannot provide the point-to-point service quality control and safety mechanisms , hackers and other malicious worm take advantage of integrated networks .

由于IP协议本身的缺陷，无法提供点到点的服务质量控制和安全机制，黑客等恶意蠕虫在融合网络有机可乘。

Compared with the traditional connection way which is point-to-point , network control system brings many advantages , but has some disadvantages , such as information transmission delay , date packet dropout and time-disorder and so on phenomena .

与传统点对点的连接方式相比，网络控制系统带来很多优点同时存在一些优点，例如信息传输时延，数据包丢失，时序错乱等现象。